Creative Twilight is a casual wargaming blog with a hobby focus. We cover conversions, sculpting, painting, and more. We also have lots of hobby tutorials, guides, and reviews for various gaming systems.
We’re just a bunch of people who like to play games. So, sit back, relax, join the community, and have fun.
In the past I had a technique I thought was OK for miniature ice effects; and it was OK, just not great. However, I’ve since discovered one product that makes far more convincing miniature ice effects. By discovered I don’t mean that nobody knows about it, just that using it is new to me.
It’s very inexpensive considering how much you get. I’ve had my bottle for years and I think this will last me another 40 years.
Mixing Your Miniature Ice Effects
The first thing I do is squirt some Still Water into a cup. Now, you can use this as-is, and just put this straight onto the base. It dries pretty clear and has a good shine to it. However, for ice it isn’t very convincing as-is and looks like water (hence the name Still Water), not so much like ice.
So, what I do is put a little white paint into it. Usually I put less than a drop in. I put a drop of white onto my palette and then take my stirrer, and put it into the drop of paint, and then mix it into the Still Water. You end up with a cloudy milky look.
The white mixed in, when dried as you’ll later see, gives it a frosted look. Ground that’s covered in snow doesn’t typically have very clear ice. Instead the ice has a white appearance with some transparency, which is what I’m aiming for when mixing in white paint.
Applying Your Ice Effects
To make the task easier I have this syringe that I suck the Still Water into. I don’t recall where I got it but it’s proven very useful for tasks like this.
Next I squirt the Still Water onto the base. If you don’t have a handy syringe then you can just use a brush and load it up. Pouring it onto the base is tricky with the model already on there.
Once I’ve got the Still water on the base I then use a brush to smooth it out some. The Still Water will pool up and doesn’t spread itself out all that well, so using a brush I push the edges of it outward so it isn’t just sitting there. It will level itself out a bit as it sits but I like to help it out.
You can see where I put the ice effects by looking for the wet milky areas. I put the ice near the base of the snow piles, and in any small holes in the snow (like that first shot – near the front). Any snow that melts would run off at the base of the pile, as I placed it, and freeze there. Plus, it just looks a bit odd when you have an ice patch in the middle of nothing.
Dry Time for Ice Effects
Depending on how thick you do the ice effects depends on how long it takes to thoroughly dry. I didn’t go too thick with it here, so I gave it around six hours to dry. I’ve done other bases through where I went pretty thick with it and it took a good 24 hours to completely cure.
A problem I ran into is where it pooled against the toes of the Helbrute. The Still Water has a good viscosity to it, but I figured it would settle down and level out against the toes. It didn’t. The result was the appearance of ice on the side of the toes, like the Helbrute has been standing there for a long time and ice built it up around its feet.
Obviously that wasn’t what I wanted, so I came back in with some snow to build that up against the toes like the Helbrute was stepping into a snow pile instead. You can read about how I do my snow in this snow basing tutorial.
I made a change though from the usual way I do snow, and did not mix white paint into the snow. Without the white paint mixed into the snow it has a more wet look; it’s slightly transparent. The idea being that where the Helbrute is stepping is into a slightly frozen snow pile, the snow pile that had melted a bit previously to create the ice remaining around that foot. The new snow added around the foot in this shot is prior to cleaning off the excess.
I also added some more iced areas while I was at it. You’ll see I added some on top of the rock on the inside and also around the lip of the base in a few areas. I just felt it needed a little more ice.
Sealing the Ice Effects
Once everything is dried I go in with a brush-on gloss sealer and seal the ice effects. I picked the sealer up at one of the craft shops in the area for a few bucks. On its own the Still Water has a good shine to it and is already convincing as ice. I just like to make sure everything is sealed and the gloss sealer does give it a bit more shine as well.
These last two shots are the miniature ice effects with the gloss sealer on it fully dried. Sorry these last two shots are dark. Here are some shots of the model completely finished, and you can see the results a lot better.
You can see some of the ice I did on my Flesh Hounds as well.
Also, here’s some shots of my Chaos Knight where I did a very deep area with the Still Water.
That’s all there is to it. It’s really simple to do as the Still Water really does all the work. You just have to coax it a bit here and there but even that is optional. I’ve done other bases where I just poured it right on, larger bases, and let it does its own thing and got some really interesting results. Snow and ice are imperfect things so don’t overdo manipulating it. Imperfections are a part of nature and help make things look more realistic.
Still Water Video
This is a video I watched when I was researching Still Water and it shows you some of what you can do with it, beyond what I have shown here with the miniature ice effects.
Please Rate This Article
Please take a second to rate this. It helps us deliver to you the stuff you enjoy.