Skip to content
Blog > Miniatures > Miniature Hobby > The Basic Structure of the Devil Dog

The Basic Structure of the Devil Dog

    This is the second part in my series on how I scratch build the tanks that I am using for my Rebel Grots army.  If you haven’t already you may want to read the first part on Gathering Materials, but it isn’t strictly necessary.

    In this post I will explain how I turn cardboard and paper into a tank shaped box that’s reasonably recognizable.  By the end of this we will have something that is good enough to use in your friendly practice games as long as your friends aren’t too picky.

    The Materials

    I start off with some high quality card stock salvaged from my recycling bin.  I’m sure you could buy some fresh card stock for this purpose, but I’m not sure why you’d want to.

    Scratch Building: Materials

    Scratch Building: Materials
    I’ve also printed my template, in this case a Hellhound template by Eli Patoroch,* on 110lb. index card stock.  For those of you who’ve used a lot of plasticard, the 110lb stock is similar in thickness to .010 styrene sheet.

    *The template I used resulted in a model that was marginally larger than the current GW Chimera kits. I’ve since re-sized a copy for a better match > 22 banewolf (2010) scaled to fit GW

    Scratch Building: Template

    Putting Together the Hull

    I cut out the pieces I want to use then glue them to the non-printed side of the cereal box using a glue stick.  You can brush on a thin coat of PVA glue instead (I sometimes do), but I find the glue stick to be a little easier to work with.

    I usually cut around the pieces rather than carefully cutting on the lines.  For these pictures I had tried folding the hull to see if the index card stock was sturdy enough for my liking.  There are people who build the whole tank from this stuff, and are perfectly happy with it, but I wanted something a bit more durable, so I glued it to the cereal box:

    Scratch Building: Template

    Cutting it Out

    Then I carefully cut the pieces out using scissors.  You can do this with a hobby knife, but I’m able to get it precise enough with the scissors.

    Where possible I’ve left the tabs longer than designed so I’ll have more surface to glue.

    Scratch Building: Template
    Next I use a hobby knife to carefully score each line where it must be folded.  If you don’t score first it is nearly impossible to get a sharp fold.

    I make sure to cut through the index card stock, and into the cereal card beneath, but am very careful not to cut all the way through.

    Sometimes the 110lb card will come off at the small tabs but for the most part I leave it glued to the cereal card.  This adds a little weight and makes it much easier to see where other parts fit because the guidelines are all visible.

    Gluing it Together

    You want to fold at the lines, not separate them!  Once all of the fold lines have been scored, I carefully fold at each line to start forming the box.  While doing this you can figure out where the tabs slip under other pieces.

    Scratch Building: Template

    Once I have an idea of where everything comes together I put superglue on each of the tabs and squeeze them into place.  This piece forms an open topped box.  The smaller piece with all of the circles goes on top of this, then the other two pieces go onto the front.  (I didn’t catch a picture of this step!)

    Track Housing

    Next is the track housings along either side of the tank.  This is basically the same process: rough-cut the paper, glue it to the card, cut it out, score, fold, glue.

    In this one you can see how much extra I usually leave on the template when I glue it down.  I don’t think there’s any point carefully cutting out each detail twice.

    Scratch Building: Template
    Scratch Building: Template
    Each of these forms a new box.  I also neglected to get pictures of these.

    There are two detail layers that are glued to the tracks.  I cut these out without gluing them to the cereal card.  The 110lb card is thick enough to add some detail on its own.  I use a 1/4″ and 1/8″ hole punch to punch out the holes in the second detail layer before I finish cutting it.  It is flimsy and difficult to punch without tearing once it’s fully cut out.

    Scratch Building: Template
    Scratch Building: Template
    This picture shows the three boxes glued together, and the two detail layers glued onto the tracks.

    Scratch Building: Template

    Track Details

    Next are smaller boxes that run along either side of the tank.

    I add extra tabs where these join to the tank because if you cut it out as is you end up trying to glue them on by the edges of the paper.

    Other than the extra tabs, it’s the same process of cut, score, glue.  I did these with just the 110lb card so I was very careful to score the fold lines lightly without cutting through.

    Scratch Building: Template
    Scratch Building: Template
    Scratch Building: Template
    The larger piece is folded and glued first, then the strip goes along the bottom to finish the box.  I found it easiest to glue these together then glue them to the side of the tank before they dry.  It’s easier to get everything square that way.

    Again, I’m using super glue for all of these joins.  Once these are on you’ve got a tank shaped box with the same size and profile as the finished model, good enough for use in a friendly game.

    Scratch Building: Tank
    In the next installment we’ll start adding details with styrene card.  I hope this has been helpful so far!

    Scratch Building Tanks

    1. Gathering Supplies
    2. Basic Structure
    3. Turret, Armor Plates & Rivets
    4. Beyond the Template
    5. Tracks
    6. Multi-melta & Metal Cannon
    7. Finishing Touches
    8. Painting
    9. Devil Dog vs Chimera #1
    10. Devil Dog vs Chimera #2
    Kamui

    Please Rate this Article

    Please take a second to rate this. It helps us deliver to you the stuff you enjoy.
    4.4/5 - (12 votes)
    Subscribe
    Notify of
    guest

    This site uses Akismet to reduce spam. Learn how your comment data is processed.

    17 Comments
    oldest
    newest
    Inline Feedbacks
    View all comments
    Thor
    Admin
    10 years ago

    Well done. I’ll have to check out the templates out there. I bet I can find something I’d use.

    Dave G
    10 years ago

    Seems like a lot of work, but for people hobbying on a budget, this is a fantastic idea… also, plenty of options for modding. I bet you could even add some colour and texture in photoshop and either not paint it or have a guide to paint on.

    Dave G
    10 years ago
    Reply to  Kamui

    I’m even thinking print them with texture and colour, then paint on top of it as a guide.

    khorneinquisitor
    khorneinquisitor
    10 years ago

    WOW. I have seen some impressive scratch-build tutorials, but this is really good in that you do it with stuff around the house for the most part and it looks the look, not like a box with a picture of a tank. Mind if I re-blog this?

    BenitoSenence
    BenitoSenence
    10 years ago

    This was a great article. I was wondering how this was done and your article was very detailed. Thanks for this. I will share this one around

    JustHippie
    JustHippie
    10 years ago

    I am enjoying this series. It seems like fun to me. I used similar techniques to build those Necron Towers with Foamcore. Can’t wait to see more.