How to Make Miniature Trees with Twist Ties

Hello all,

A couple of weeks ago I posted a couple of test trees I made while trying to work out  a method I was happy with.  This tutorial will demonstrate the process I settled on to get reasonably convincing model trees without breaking the bank.

First up, here’s a list of items you’ll need:

making the wire armature for Miniature Trees

The wire armature is the primary component of the tree.  I am using plastic coated garden twist tie to make my armatures because it’s a cheap way to get lots of material.  You can use any twist ties, or even pipe cleaners, you have available.  Un-coated wire could be used but you’ll need much more of it to build up bulk.

Miniature Trees Materials

Start with a bundle of twist ties.  The number you use will determine the girth of the tree and number of branches, the length will determine the height.  For this tree I am using 12 strands cut 6-8 inches in length.  Don’t worry about lining them up as you bundle the twist ties.  Just group them up and twist the whole bundle to start forming the trunk.  Leave about an inch untwisted at one end and work toward the other end.Miniature Trees - Making the Trees #1

After you form the trunk you can start forming the branches.  Separate a few strands from the bundle, making sure to take one or two from the opposite side and pull them though the bundle.  This will help lock the branch in place.  More strands means a thicker branch.Miniature Trees - Making the Trees #2Twist the branch starting from the trunk and moving toward the end.  As you work away from the trunk you can further split the bundle to form smaller branches off the first.  Leave about a half inch to one inch of each strand untwisted so you have something to glue the foliage to later.  If you’re making dead or winter trees you can twist them all the way to the end so they aren’t so flat. Miniature Trees - Making the Trees #3

After forming the first branch continue twisting up the trunk and splitting branches off as you go.  Continue this process until you’ve twisted all of the strands into branches.Miniature Trees - Making the Trees #4

Miniature Trees - Making the Trees #5

Now that you have the basic tree formed you can address the loose strands where you started.  Split these into two or more groups and twist each into a root.  These will create the impression of exposed roots, and they also give you something to glue down to the base (if you don’t want an exposed root system you can spread the bottom strands out without twisting them so they are easy to cover up after gluing down.)  With the roots formed you should be able to stand the tree up.  Bend the trunk and branches around until you have the tree shape you are looking for.Miniature Trees - Making the Trees #6I decided that the lowest branch looked a little too thin.  If you want to bulk out your tree at this point it is easy to add more twist ties.  I start by lining the new strand up with an existing branch.Miniature Trees - Making the Trees #7

Related Reading  Thor's Workbench: Soulgore Dress-up - Feedback Needed

Then I twist the new strand onto an existing branch to make it thicker.Miniature Trees - Making the Trees #8I continue to work my way down the branch and trunk until I’ve twisted the rest of the strand around the tree.  You can add as many new strands as you want to thicken branches or even add new ones.  Make sure the strands you add are long enough to make it all the way down the trunk.  This will ensure that the trunk appears thick enough to support any branches you thicken/add.

Base Mounting the Miniature Trees

Now that I have a tree shape I am happy with I am ready to mount it on a base.  Whatever you use as your base make sure it is large enough to be stable.  The only reason trees stay standing in real life is that they have extensive root systems hidden below the surface.  Without that in your favor you need a wide and/or heavy base to keep your tree stable.  For the test trees in my earlier post I used some flying bases I had sitting around.  For this one I decided to use a chunk of vinyl composite flooring because it’s heavy and the more random shape is fitting to scenery bases.  It’s also pretty cheap at 70 cents per square foot.  There isn’t much flat surface on the roots so I used an epoxy putty to attach the tree to the base.  This is a two-part putty similar to Kneadatite (green stuff) but it is stickier and only has a 5-minute work life.  It’s crap for sculpting but it’s great for holding things together.Mounting the Miniature Trees

Coat the Miniature Trees

After the putty is fully cured I trimmed the root tips flush with the base.  Then I used pre-mixed grout to add “dirt” to the base, leaving the tops of the roots exposed.  Then I coated the tree with all-purpose joint compound.  This hides the twist ties and creates a nice, knobby bark texture.  It also make the tree more rigid.Tree Tutorial (12)

Painting the Miniature Trees

Now it’s time to paint!  I used an airbrush for this but you can go with bristles or spray cans if you prefer.  First a couple of coats of black primer.  Tree Tutorial (13)

Then brown…

Tree Tutorial (15)

and a tan highlight…Tree Tutorial (16)Then some golden brown for the base.Tree Tutorial (17)And finally a light tan highlight for the base. Tree Tutorial (18)

Details & Foliage for the Miniature Trees

I don’t worry about getting as detailed or clean a paint job as I would with most of my other models.  Trees don’t require much to look good.  Next I decorate the base using similar methods as I used on my stepped hills.  I coat most of the base with watered down PVA glue (Mod Podge in this case.) Tree Tutorial (19)I add clumps of static grass.Tree Tutorial (20)

And with the glue still wet I submerge the base in a small container of green flock.  I hold the base over the container and tap it to knock off any excess.  Tree Tutorial (21) Next I add foliage.  I am using clump foliage for this.  It’s a lot like flock but in big chunks.  I separate some nice big pieces from the smaller bits.  Tree Tutorial (22)

Then I use superglue to attach them to the ends of the branches.  First I glue a piece to the top side, then I add a second piece to the bottom.  I haven’t had great luck using PVA for this but it does work well to attach clumps of the foliage together.  I put a little superglue on the twist tie, then add some PVA to the clump foliage itself.  Tree Tutorial (23)

Related Reading  Thor's Workbench: Flesh Hounds of Khorne

Keep adding foliage to the branches until they’re all full voila, tree!  In some places I’ve used PVA to add more foliage directly to the larger clumps to bulk them out a bit.

Tree Tutorial (24)  After all of the glue dries I give this a coat or two of matte sealer to protect the paint and help hold all of the foliage together.  Here’s a shot of the finished tree i the sunlight.Finished Miniature Trees

In this last photo you can see the new tree next to the two test models.  The middle tree shows how this process looks with leafless trees.  The tree on the left was done without coating the twist ties before painting.  As you can see the tree still looks good without it, just different.  I plan to use a mixture of these three looks to add some extra variety to my forests.Finished Miniature Trees

So there’s my method for making trees.  It’s dirt cheap and looks decent.  How do you like them?  Do you have any ideas to improve the process?

 

  • Great job. Very easy to follow tutorial with great results. I can’t think of anything I’d do differently.

    • Thanks! Now I just need to make a couple dozen more to replace my old aquarium plants…

  • This is a fantastic tutorial. Just wow. Your trees look much better then most I’ve seen online.

    My only suggestion to improving the process is going to be artist based. Using a bit of variety in the foliage in the tree would change your season, or give you different effects.

    • Thanks! I agree that different foliage would add some nice variety. I currently only have the one color but clump foliage is available in a wide variety of colors. It would be easy to mix in different shades of green or to add some autumn colors to mix it up a bit. Using different materials such as lichen to create foliage would add even more variety without a lot of extra work.

      I will do a little experimenting in the future. If I find anything that I like I’ll be sure to post it.

  • Hah! That’s awesome. I went all out with my trees, making them from cardboard tubing, but that made larger trees than this (shameless self promotion: http://www.spruegrey.com/wargame-scenery-trees-ii/ ). The twist ties made for excellent trees and I plan on stealing this idea. So ner.

    • Thanks, loot away!

      I’ve actually seen that post before! It’s a great use of cheap materials and a very interesting piece. Giant tree trunks like that are a nice way to break up shooting and movement lanes on a wooded table.

  • Sin Synn

    yeah, solid stuffs here.

    I gotta start getting a 6×4 foot table together (my Infinity table won’t cut it for FoW and 40k), so I see some projects like this in my future…

    • Thanks!

      If you build them assembly line style these can go together quickly. I like buildings and ruins but trees and hills are much easier for me to slap together.

%d bloggers like this: