- Learn How to Scratch Build Tanks #1 – Gathering Supplies
- The Basic Structure of the Devil Dog
- Building the Turret, Armor Plates, and Rivets
- Going Beyond the Template
- Adding Tracks to the Devil Dog Build
- Scratch Building a Multi-melta and Melta Cannon
- The Finishing Touches on the Devil Dog Build
- Scratch Built Devil Dog Painted
- Scratch Built Chimera vs. GW Chimera – Part 1: Early Build Comparison
- Scratch Built Chimera vs. GW Chimera Part 2: Finished Build Comparison
I have had a lot of questions regarding the tanks I have been scratch building for my Rebel Grot army so I decided to write a tutorial as I build my Devil Dog. Once I get moving it’s easy to forget to take pictures. Please let me know if there is a step where you would like to see more pictures. I’ll need to build a couple more Chimeras soon and they’re very close to the Devil Dog kit so I can fill in gaps later.
First of all, why scratch build?
There are a lot of reasons to scratch build. You may be looking to save some money. Material costs can add up more than you might expect, depending on what you’re using, but you will probably still come out way ahead in cost. If you go all out on high quality materials you could spend as much as $10 on a single tank but if you’re frugal it will probably be closer to a buck or two.
In either case you’re way below $65. It’s also common to scratch build because you want something different from the standard kit. For me it’s a healthy mix of the two.
If you are looking for an easy route then scratch building is the wrong way to go. The toughest GW kit I’ve assembled was still easier than anything I’ve scratch built. However, it might not be as tough as you think.
For my builds I want something that looks like an Imperial vehicle that has been commandeered by Orks or Grots. By the time I were to cut off what I didn’t want and slap on what I did, I think it would be about as much work to do a good conversion as it is to scratch build. Since I’m looking at a similar amount of work either way I figure I might as well go the cheap route!
If you want something that looks exactly like the official kit then you should seriously consider whether you’d rather spend the time or the money.
I’m going to scratch build, so what do I need?
For any scratch build you should have a pattern to work from. This makes it easier to ensure you get the sides equal and everything square. I’ve drawn my own in the past. My battlewagon is an example of this:
For my Rebel Grots I’ve been using papercraft templates I found online*. If you look for templates made by Eli Patoroch you’ll find some really good stuff. I don’t know who he is but he’s made a ton of templates!
These provide a detailed build that looks very much like the GW kits when assembled. For this tutorial I’ll be working with his Hellhound template.
*Note: Finding the templates has become difficult since writing this. However, I have uploaded the template I’m using to the blog.
You will need to decide what to use for materials. Styrene sheet, or plasticard, is very popular and for very good reasons. It is fairly cheap, quite durable, and can produce fantastic results. It can take a little getting used to but overall it is easy to work with.
One nice thing about styrene is that it’s the same material used for the plastic GW kits so the end result will have very similar weight to the actual kit. It will also take paint, glues, etc. the same way as the kits you are used to working with. I also like that you can drill and cut into it to create battle damage. I did my first Basilisk with plasticard:
For this tutorial I am starting with cheap card stock. The templates were printed on 110lb. index card stock so the pieces will have a bit of definition on their own. A lot of papercrafters stop at that as it’s reasonably durable once it’s glued together. I want mine to be a bit more durable though as I’ll be adding plastic bits later.
For the primary structure I’m using some high end materials looted from my recycling bin:
Yeah, it seems a bit trashy (pun intended) but it works pretty well if you know how to work with it. If you use some plasticard armor plates over the card stock core it’s difficult to tell from a pure plasticard build once it’s painted. You can see that with my two Leman Russ Exterminators below:
Another material that works well is matboard. It’s a heavy card stock used for framing. It can be tough to cut because it’s so thick, but it is durable. The battlewagon showed above is a matboard core clad in styrene armor plates.
So, for this build I’ll be using cereal box, index card stock, and styrene to build most of the tank. I also use a lot of random styrene rods and bits for detail. GW weapons and vehicle bits are great if you have them handy.
Here’s a quick list of the other items I’ll be using:
- Hobby Knife
- Super Glue
- PVA glue (I use Modge Podge)
- Glue Stick
- Steel Ruler
- Cutting Mat or Board
- Green Stuff (Kneadatite Epoxy Putty)
- GW Liquid Green Stuff
- Hole Punches (1/4″, 1/8″, 1/16″)
- Maybe some other random stuff I’m forgetting…
So, now you’ve got a list of junk to round up if you want to follow along. In the next part of the series I’ll explain how I turn that cardboard and paper into a basically tank shaped structure. After that we’ll start adding the details that will make it less like a box and more like a proper tank!